RXM39.1 properties

The listed properties are displayed in the Hardware and network editor > Inspector window > Properties tab when the device with KNX PL-Link is selected in the Device view tab.

RXM39.1

General and Catalog information

The General and Catalog Information group provides information about the device.

Property	Description	Default value
Mode	Mode shows the network mode of the device. Read only.	KNX PL-Link
Name	Name is a text field to enter the name of the device. The name is used to identify the device in the device view.	Depends on other settings.
Comment	Comment is a free text field to enter any helpful information on the device.	-
Power consumption	Power consumption shows the power the device consumes. Read only. Unit: [mA] The value is used to calculate the remaining power of the KNX rail. See also power consumption and supply on KNX rail of PXC3 or KNX rail of DXR2.	Depends on the device type.
Short designation	Short designation shows a short description of the device. Read only.	Depends on the device type.
Order number	Order number shows the device type. Read only.	Depends on the device type.
Version	Version shows an internal version of the device. Read only.	-
Description	Description shows a short description of the device. Read only.	Depends on the device type.

Device information

The Device information group provides information about the device and settings.

Property text	Description	Default value
Device address (KNX)	Device address (KNX) shows the fixed standard address for devices with KNX PL-Link. Read only.	255
Serial number used	Serial number used defines the method used for device identification. : The serial number entered in the text field Serial number is used for device identification. : Device identification has to be done in Web interface. The device has to be in programming mode for Web interface to perform the device identification.	: Device identification has to be done in Web interface.
Serial number	Serial number defines the serial number used for device identification. Serial number is only enabled and relevant if Serial number used is enabled.	000000000000

Property text

Description

Default value

Device address (KNX)

Device address (KNX) shows the fixed standard address for devices with KNX PL-Link. Read only.

255

Serial number used

Serial number used defines the method used for device identification.

: The serial number entered in the text field Serial number is used for device identification.

: Device identification has to be done in Web interface. The device has to be in programming mode for Web interface to perform the device identification.

: Device identification has to be done in Web interface.

Serial number

Serial number defines the serial number used for device identification.

Serial number is only enabled and relevant if Serial number used is enabled.

000000000000

Alarming

Property	Description	Default value
Alarming	: Alarming is disabled. : Alarming is enabled. An Event Enrollment (EE) object is created.	: Alarming is disabled

Property

Description

Default value

Alarming

: Alarming is disabled.

: Alarming is enabled. An Event Enrollment (EE) object is created.

: Alarming is disabled

Functions

The functions table in the Channel Overview provides an overview of the channels of the device. Depending on the device the values in the table are read only or can be edited. The available types depend on the device and the application function.

Property	Description
Name	Name of the channel. Read only.
Type	Name of the function.
Zone	Part of the geographical address of the device. Range: 1...126
Room	Part of the geographical address of the device. Range: 1...63
Subzone	Part of the geographical address of the device. Range: 1...15 Note Each channel has to be in a separate subzone.
Activate	Activate defines if the channel is activated. : The channel is activated. : The channel is deactivated and is not considered in the calculation of the limiting factors of the automation station.

The functions are described briefly in the table below.

Type	Description	Number of channels used
Device	Device information that is mapped to the BACnet object peripheral device (PrphDev). Read only.	1
EHEA	Electrical heating element actuator	1
FSA	Fan speed actuator (FSA) for continuous fan actuators (ECM, DC 0…10V)	1
GPDI	General purpose digital input (GPDI) for window switch or presence detector among other uses	1
GPTS	General purpose temperature sensor (GPTS) for room temperature Only LG-Ni 1000 sensors are permitted.	1
HVA	HVAC valve actuator (HVA) for continuous valve actuators (DC 0…10V)	1

Some of the functions can be configured. The properties of those functions are described below in order of their appearance in the table.

Electrical heating element actuator (EHEA)

Property	Description	Default value
Polarity inverse	Polarity inverse defines if the received on/off control value is inverted before actuating the electric heater release relay Q13-Q14. : The received on/off control value is not inverted. : The received on/off control is inverted.	: The received on/off control value is not inverted.
Backup value	Backup value defines the actuator position if the timeout for receiving a setpoint for the actuator position has passed. Backup value is only relevant if the property Backup mode is set to BackupValue. Range: 0...100 [%]	0
Backup value fan	Backup value fan defines the value for the electric heater release relay if the timeout for receiving a setpoint for the actuator position has passed. Backup value fan is only relevant if the property Backup mode is set to BackupValue. : Off : On	: Off
Backup mode	Backup mode defines the behavior of the actuator if the timeout for receiving a setpoint for the actuator position has passed. BackupValue: The actuator goes to the value defined in the property Backup value. Keep: The actuator keeps the last valid value. Off: The actuator goes to 0 V in case OutLevel0Percent >0.	BackupValue
Output	Output defines the method for the active power control method and hardware outputs: Proportional On/Off On/Off & Proportional	: On/Off & Proportional
Reference value at 0 %	Reference value at 0 % defines the level of the physical output for a process value of 0%. Range: 0…100 [%]	0
Reference value at 100 %	Reference value at 100 % defines the level of the physical output for a process value of 100%. Range: 0…100 [%]	100

Fan speed actuator (FSA)

Property text	Description	Default value
Fan release	Fan release defines if the second relay (Q33-Q34) is used as fan release relay. : The second relay (Q33-Q34) is not used as fan release relay. : The second relay (Q33-Q34) is used as fan release relay.	: The second relay (Q33-Q34) is not used as fan release relay.
Backup value	Backup value defines the fan speed if the timeout for receiving a setpoint for the fan speed has passed. Backup value is only relevant if the property Backup mode is set to Mode 0. Range: 1...100 [%]	1
Polarity inverse	Polarity inverse defines if the received on/off control value is inverted before actuating the fan release relay Q33-Q34. : The received on/off control value is not inverted. : The received on/off control is inverted.	: The received on/off control value is not inverted.
Backup value fan	Backup value fan defines the value for the fan release relay if the timeout for receiving a setpoint for the fan speed has passed. Backup value fan is only relevant if Backup mode is set to Mode 0. : Off : On	: Off
Backup mode	Backup mode defines the behavior of the actuator if the timeout for receiving a setpoint for the fan speed has passed. Mode 0: BackupValue: The actuator goes to the value defined in the property Backup value. Mode 1: The actuator keeps the last valid value. Mode 2: The actuator goes to 0 V in case OutLevel0Percent >0.	Mode 1
Reference value at 0 %	Reference value at 0 % defines the level of the physical output for a process value of 0%. Range: 0…100 [%]	0
Reference value at 100 %	Reference value at 100 % defines the level of the physical output for a process value of 100%. Range: 0…100 [%]	100

General purpose temperature sensor (GPTS)

Property	Description	Default value
Change of value, COV	Change of value, COV defines the change in the value for room temperature that triggers the sending of the value for room temperature. Range: 0.1...100 [K]	0.1

Property

Description

Default value

Change of value, COV

Change of value, COV defines the change in the value for room temperature that triggers the sending of the value for room temperature.

Range: 0.1...100 [K]

0.1

HVAC valve actuator (HVA)

Property text	Description	Default value
Backup value	Backup value defines the actuator position if the timeout for receiving a setpoint for the actuator position has passed. Backup value is only relevant if the property Backup mode is set to Mode 0. Range: 0...100 [%]	0
Backup mode	Backup mode defines the behavior of the actuator if the timeout for receiving a setpoint for the actuator position has passed: Mode 0: The actuator goes to the value defined in the property Backup value. Mode 1: The actuator keeps the last valid value. Mode 2: The actuator goes to 0 V in case OutLevel0Percent >0.	Mode 1
Reference value at 0 %	Reference value at 0 % defines the level of the physical output for a process value of 0%. Range: 0…100 [%]	0
Reference value at 100 %	Reference value at 100 % defines the level of the physical output for a process value of 100%. Range: 0…100 [%]	100